It then further protects the surface by forming a film with low permeability to water vapour and oxygen. Vactan is self priming but for long term protection it is advisable to overcoat with a suitable water or solvent base midcoat or topcoat. One litre of Vactan can treat square meters. This non hazardous product has been tested and certified as fit for use for the carriage of grain and use in potable water systems. Vactan should be used within 12 months of the purchase date, do not allow Vactan to freeze.
Store in ambient conditions out of direct sunlight. Surfaces should be wire brushed to remove loose rust and it is preferable to remove soluble salts by washing with water as they inhibit the conversion process. Surfaces should also be oil and grease free.
Vactan has been designed for application by spray and brush. By airless spray a dry film thickness of 60 microns can be achieved without sagging. The addition of further water may be necessary for air assisted spraying. By brush application, a dry film thickness of 40 microns per coat is considered optimum.
Vactan can be applied over damp surfaces and dries quickly under suitable temperature and humidity conditions. Immediately after use equipment should be washed in water to remove all traces of Vactan. Under ideal conditions a micron wet film of Vactan will be touch dry in approximately 10 minutes at 20 Deg C. Whereas at 10 Deg C and little air movement this time could be as much as 2 hours. Ideally wait 24 hours after application.
Vactan may be overcoated when cured with any conventional paint brush, roller or spray. The test piece shown here was overcoated with one coat of 2-pack polyurethane acrylic, applied by spraying.
Vactan has been tested and certified for use in the carriage of grain and use in potable water systems. It may also be used in sensitive foodstuff areas. The information given is based on our experience and reports from customers.
Knock off the scale and leave the rest for the best results. It took just under a gallon to do a 16 foot trailer frame. It lays down a great base to paint over. This is really thick stuff! I used this to try and preserve the frame on my jeep grand Cherokee. I have never used anything like this before but it seems to cover well. I am curious to see how durable it is.
My camper trailer had spots that needed to be treated for rust. This worked excellently and coded very well. Several areas where different metals join together like the platform that the propane tanks set on, this was able to adhere very well and not be too thin and run off.
I applied black paint to the trailer after this dried and it held very well. Very happy with the product. On my automobile I had one small area from an accident that creased the metal and the paint was peeling in a small bit of rust was forming.
I applied with a brush to that area and then use some touch up paint. Overall a wonderful product to have in my shed with other tools so I can use it when I see any rust. Fairly impressed with this stuff. I prepped the bottom of a truck bed with a wire brush wheel on an angle grinder — knocked off the loose rust, dulled the existing paint everywhere I could with 80grit sandpaper.
Waited a full 24 hours, did another coat where I thought it needed it, waited another 24 hours and then did a top coat over it with some spray-on undercoating.
It cures HARD and has held up to salt roads in the winter with no new rust or flaking paint. Great stuff. I bought this for using on my big catering rig. So far it has provided a good surface prep for paint and held up to the heat. This was amazing! This product delivers all on claims. Ease of use. Have rust? Overall, this product worked very well. Although initial mixing is tough because it is very thick, adding water thins the paint, making application very easy with a spray gun.
If you are using a brush then adding water is not needed but it will apply very thick. Was not easy to find this in non-aerosol form for some reason. Perfect from spot jobs or whatever. Easy to apply… works as stated. Shipping was on time and no complaints, satisfied customer.
I used this on a wrought iron fence that was in trouble. The product went on easy using an old sock to wipe it on. The redish color made it easy to see while painting black. I will use this product on any future needs — great product. We used it to stop the rusting of our Bilco doors, which are over 35 years old and had a fair amount of rust. Not too much scraping to prepare the surface.
Went on easily and dried to touch quickly. Very easy cleanup. Awsome coverage and easy to apply. Drys to the touch fairly quickly and bonds with the rust quickly as well. You can see a slight color change in the floor board where the paint is interacting with the rust. I used this in restoring a truck frame.
Its easy to spray and covered well. Only wish it came in black. I used a LVLP spray gun with good results. Brushed on and sprayed easily, coverage is better than expected. Leaves a tough surface, hopefully does well on buried pipe. I was hesitant to purchase but, went for it. I even search YouTube and watch all of them. Boy, I was glad that I did. I live close to the ocean and all metal in my back yard rust. Now with xionlab, they will last for a long time.
I recommend this product. Amazing product. I received my first order and it had globs in it. Almost impossible to mix back to desired consistency. I used it on a jeep axle.
Only time will tell the longevity of product. This stuff is great. I bought this for my rusting Take 3 trailer and it does great once I get it fully covered I plan to just paint over it. Easy to apply, minimal preparation, very hard finish, easy clean up.
This product works exactly as described. Made a carport from old oil field pipe. Used a bucket and car sponge to apply. One coat was more than adequate if painting over it. The application went well. A single coat has covered well, it has a lot of solids in the mix, but not at all too thick.
I did not have heavy rust to cover, just smooth surface rust that I prepped with a good scrub with a wire brush. It dried to a hard finish. Roller cleaned up easy with soap and water. Perfection in a can! Used in a large and serious project refinishing rusty steel support beams in a modular home.
No need to look for anything else. Be aware that brushing on an acrylic enamel over this primer will cause this primer to run even though fully cured. Other wise this is an excellent product that goes on smoothly, kills the rust and the smell is not as strong as other products I have tried.
I will purchase again. I took a chance on this to treat some surface rust on some freezer panels I was using to line an aircraft hangar with.
Love this stuff! Sprays nice , dries fast. One gallon goes a long way. Will but again for anything related to rust treatment. Super easy to use clean up is easy this product is amazing painted over rusty metal and leave it outside for 1 week the results are amazing.
It was easy to spray it on and I put a topcoat over. It cures really hard. You must be logged in to post a comment. Please leave this field empty. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Duis lacinia lectus quis turpis viverra posuere. One gallon of product covers up to sq. Can be applied with a brush, or spray gun.
Water-Based, can be applied to a damp surface, does not trap moisture, can be diluted with water. Tools clean up with water. One-step rust converter and primer coating. No topcoat is needed. Accepts a wide range of coatings, not just oil-based. Prevents corrosion. UV and Hydrogen sulfide resistant.
Contains no lead or heavy metals. Made in USA. High Quality. Terra Care Certified. Free Shipping. Our rusty metal primer is specifically designed to stop rust by converting EVEN DAMP rusted metal surfaces to phosphate without heavy scraping or sandblasting! COVER 2. Our rust neutralizer will cover up to square feet per gallon, and up to sq. You can easily apply oil-based, water-based, enamels, or any other top coating you like. OR you can go ahead and save your hard-earned money and skip on the top coating since our industrial-strength rust remover and primer do not require a topcoat!
Our mission is to offer you pro-grade solutions for your renovation or construction projects. No bad odour. Fresh Color. Safe on Pipes. No toxic fumes. Cover 2. Environmentally Safer Formula Our water-based formula is a professional-grade corrosion converter that is safer for environment.
Cleaning Your Tools Is A Breeze Thanks to our water-based formula, your tools can be washed quickly without any soap or chemical products.
Bonds With Rust STEPS 1. FAQ Can I use a garden sprayer? Yes…one coat, our rust converter should be ok. What pressure setting is best?
What do I need to do to apply this product with a spray gun? Can I use your rust converter on my new steel parts that are not rusty as a primer? Can I use XionLab Rust converter Primer on part vehicle parts such as rear end, crossmembers, brackets and other small parts?
If I scrape all loose rust and then apply two coats, will it extend the life of the pan? Our product will protect your pan from further oxidation and thus extending its useful life. What is the minimum temperature that your rust converter can be applied? We do not recommend using our rust converter under 50 degrees.
Will it be ok to pour concrete around the treated rebar. I live in an area with temperatures goes below zero. Do I need to be concerned that my converter was exposed to below freezing temperatures? Will your product adhere to a galvanized steel roof that is rusted?
My one concern is that your product dries to a red color and I am looking for a final color of black. Is it possible to add a dye pack or pigment to your product to achieve this?
0コメント